How To Repair A Punched Hole In The Wall

When a stroppy teenager doesn't get their manner the first matter they desire to do is dial something, and this normally leads to a punched hole in the wall!

If isn't a fist, its an Xbox controller and cheers to FIFA twenty, there are alot of teenagers punching walls over their lost matches…whats the world coming too??

The thing is, subsequently the harm has been washed virtually parents achieve for the metal patch you can buy from your nearest DIY store.

They do the chore, don't go me incorrect, but the finish is poor, even if you're practiced with a filling knife.

I have a ameliorate style of patching up a wall using a repair chosen 'The California drywall Patch'.

The California drywall patch method is probably the cheapest and gives you a better finish than most (if not all) patching methods.

How To Fix a Punched Hole In The Wall – YouTube Episode 2

What Practice I Need to Fix a Punched Pigsty In The Wall?

When using the California drywall patch method for fixing a punched hole in the wall, you won't need any expensive tools, but I practice recommend you have the tools I suggest considering they will make the chore alot easier, and they are…

Pencil

Ruler

Stanley pocketknife

Dry wall saw

12 inch Taping knife

Plastering Militarist

five in ane tool/filling pocketknife

Filler – I recommend Gyproc's Easi-fill up jointing compound

A scrap piece of plasterboard/drywall

Sandpaper, sanding block

How To Gear up A Punched Hole In The Wall Steps…

Stride One – Check For Wires and Pipes

Using your fingers, carefully remove the damaged slice, and have good feel circular (all 360 degrees) for any wires or pipes.

Step Two – Prepping The Hole

Using a drywall saw carefully start to saw the round hole into a square hole.

Pace Three – Making The Patch

Offer the Backside of your chip slice of drywall upto the square pigsty y'all've made.

We desire a 2 inch overhang all around the expanse of the square, marker each measurement onto the scrap piece of drywall.

Rotate the drywall 90 degrees and brand another ii, 2″ wide marks.

Using a ruler or a direct edge join those measurements together to make a foursquare.

Once the lines are drawn, nosotros need to cut the square out using a Stanley knife.

Gently score ane line starting time, then hold the plasterboard and tap with your commencement on the opposite confront of the plasterboard directly in line with the scored line you've only made.

Repeat the above process again for the other scored line.

Y'all should now have a square that when offered up to the pigsty in the wall gives you a ii inch overhang on all sides.

With this cut drywall square nosotros now need to transfer the inside dimensions of the square pigsty on to it.

And you lot this by offering it support to the hole, making certain your 2 inch overhang is equal on each side.

Grab a pencil then make ii marks a quarter of an inch shorter of the edge.

Now using those marks nosotros need to join them upward once again until you have some other foursquare in the centre of the drywall.

Score forth each line one at a time, but instead of cutting the scored piece off, we want to peel the plaster from the paper instead (see video likewise).

Hey Presto! you should now take a California drywall patch ready for activeness!

Step Four – Test Fit Patch

We now need to test fit the California drywall patch to make sure information technology fits into the foursquare hole nosotros made earlier.

By placing the patch over the hole without applying likewise much force per unit area try to push the patch into the hole.

If the patch doesn't fit, then adjust the hole not the patch, past running your Stanley knife or drywall saw around the within edge of the hole until enough drywall is removed so the patch tin slide in and fit flush.

At present offer the patch up to the hole again and information technology should fit prissy and comfortably in the wall without adding also much pressure level.

Step Five – Mix Filler

Using your hawk, cascade some dry filler onto it, then make a crater in the heart of the filler.

We want to add together hot water to the filler considering information technology volition speed the drying time, helping this patch be a quicker fix than normal.

If your scared of a fast drying time, just add together common cold water.

Give the filler a good mix using your filling/putty knife until the filler resembles whipped cream.

Step Vi – Applying Filler To The Hole and Patch

Load up your filling/putty knife with filler and paste on all four sides of the hole.

So belongings your patch identify filler into the corners of the four sides where the paper meets the plaster.

This will ensure no air pockets class when you push the patch into the pigsty, information technology besides creates a stronger repair.

Take the loaded patch and identify into the pigsty, using your putty knife push on each corner to brand sure the patch sits affluent with the wall.

Gently with the filler/putty pocketknife, slide the knife across the newspaper edges until the paper is stuck downwards with the filler

Removing any excess filler as you go.

Step Seven – Skim The Repair

With the leftover filler, grab a 12″ taping pocketknife, scoop the filler upwards and skim the filler across the repair.

Effort to keep your taping knife at nearly 20-30 degrees every bit you pull it across the repair.

Don't exist as well perfect because y'all will exist sanding this coat down one time it'due south dry

Stride Eight – Sand Down First Skim and Apply 2d Skim

At present the first skim coat is dry we need to sand it downwards until it is smooth and affluent to the surface of the wall.

Mix some other application of Easi-fill on your hawk.

SHERLOCK MAINTENANCE TIP: If you find too hard to mix the filler on your hawk, pour the filling compound into an old container, add together water and mix. Once it resembles whipped cream transfer it to your hawk…Sorted!

Apply the second glaze of skim slightly wider than the offset glaze of skim. This helps plume the repair back into the wall.

Step Nine

Wait for the second coat of skim to dry and repeat the same sanding process making sure all ridges and high spots are sanded down affluent with the wall.

Then wipe down sanded expanse with a slightly damp cloth.

Step Ten

Now get painting your repair.

If you find after the pigment dries there is some high spots or ridges you lot may of missed when sanding, just wait for the paint to completely dry, rub down and repaint.

Did This Mail Help?

Hopefully you now know how to fix a punched hole in the wall.

It is a great skill to have, filling holes this way is by far the best repair.

Permit me know if you establish it easy following the steps to a higher place in the comments section below.

Each and every week I put my heart and soul into providing you with cracking content to aid with any DIY jobs effectually the home.

If you think this postal service could help someone yous know, please share.

Other Helpful Maintenance Manufactures

Refelting a Summer House Roof Refelting a summertime business firm roof is quite a big chore but its definitely something you don't want to put off, Follow my pace by step guide.

How To Maintain Your House – The Bound Home Maintenance Checklist With spring effectually the corner it makes perfect sense to check what maintenance your house may need for the season and the coming months ahead

How Much Laminate Flooring Exercise I Need For My Room? Non sure exactly how much flooring y'all'll need? Follow this easy peasy guide and feel like a PRO!